標題: [教學] tosihba flashair wifi for 3dPrinter(先査證自己3DP是否支援） [打印本頁]

---

作者: Kawai.jolly    時間: 2015-7-17 19:27     標題: tosihba flashair wifi for 3dPrinter(先査證自己3DP是否支援）

本帖最後由 Kawai.jolly 於 2015-7-20 01:04 編輯

我試左暫時沒有問題，幾好用，唔洗成日扲出拎入張卡咁麻煩



http://microfabricator.com/blogs ... ith-your-3d-printer

1.檔案總管入面Set番見到隱藏File及Floder

2.用window個Notepad打開佢講果個sd_wan/config，加番佢個啲野，現有個啲留下

[Vendor]

UPLOAD=1
UPDIR=/
CIPATH=/DCIM/100__TSB/FA000001.JPG
APPMODE=5
APPSSID=TOMJONES
APPNETWORKKEY=GREENGRASS
APPAUTOTIME=0
APPNAME=printer01
VERSION=F19BAW3AW2.00.03
CID=02544d535730384708ccc4a67800e501
PRODUCT=FlashAir
VENDOR=TOSHIBA
MASTERCODE=e4121d4499e2
LOCK=1
APPINFO=0000000000000000


講解下
Appssid就係你個wifi
APPNETWORKKEY就係你個wifi嘅password，一開個時會變曬***你照打番落去
Mastercode係張卡的Mac，卡背後有寫
其他野冇就加番，有就保留



3.安全unplug張SD卡，再插番入就可以

你已經可以插入3Dp入面試下

4．192.168.1.200/upload.cgi
就係你上載時用瀏覽器打呢隻Link，記得ROUTER入面set死個ip比呢張卡，唔係下下揾張卡的lP仲煩我用192.169.1.200

---

作者: palpatrick    時間: 2015-7-17 20:25

非常實用! 我有張 pqi air 未知support 如何!

---

作者: Super169    時間: 2015-7-17 23:13

本帖最後由 Super169 於 2015-7-17 23:15 編輯



正喎, 我張 SD 就黎比我隊爛了.  閃豬個 slot 既窿好到好大, 唔可以沿邊入, 成日對唔正.
剛 check 左, 16G 約2 舊水, 都可以接受.  如果 8G  可以 1 舊就更好, 反正多左都無用.

---

作者: fred2088    時間: 2015-7-18 00:07

回覆 3# Super169


    TB ... 108 人仔 ...   成HKD150 到港 ...

---

作者: Super169    時間: 2015-7-18 01:51




price.com 格價都係 180 左右, 差幾十蚊, TB 買呢D野, 有問題要換比較煩.

---

作者: lawhun0083    時間: 2015-7-18 10:01

香港邊度有得買?

---

作者: dtom    時間: 2015-7-18 12:31

wifi sd card 咋，又唔係新科技，各大電腦/影音鋪都有得賣

---

作者: Kawai.jolly    時間: 2015-7-18 16:58

四圍都有，腦場16G先一百八十幾，真係勁方便

---

作者: Super169    時間: 2015-7-18 17:56

行行下街，上左诲鮮坊，放低两舊四十二，執左張32GB。
本來諗住買最細8G，睇完佢既介紹，去旅行影完相用 tab 即睇，又幾正喎。結果決定買最大既。

---

作者: Super169    時間: 2015-7-18 22:19




ching 我今日買左番黎, 剛剛番到屋企, 攪左一陣....唔知點 set, 原來唔係想像中咁直接.  
我仲以為 set 番部 router 既 SSID 同 password 比佢, 就識得自己上網, 我就可以見到佢.  點知做完都唔知點.

我用 card reader 插入部電腦, 裝左佢個 FlashAir Tool.  出左 4 個 option:


理論上都係由頭落去, 咁我做左 Network Settings 先, 睇落好直接, 填左幾格(比我油黑左果 D).


Wireless LAN setup mode 我選 Automatic startup mode, 再改埋 30 分鐘至 timeout (睇落都無錯掛, 比多D時間摸索下).


之後選 FlashAir drive setting, 諗住睇下有乜好選....點知好話:

唔通要我部 PC 有 WiFi?  我估係去旅行時, 無 router 至用掛.  暫時唔理佢.

Initialize the card/change settings.... 睇落唔似有需要用.


斷估應該 set 哂喇, 就插去比隻閃豬食, 諗住試下抄個 file 比佢印......問題黎了, 點抄?

手機既 WiFi 見到佢, 裝埋個軟件, 可以見到張卡既 file.  但只係可以抄落黎, 唔可以抄上去.

而且, 我部 PC 都仲係見佢唔到.  無計唯有試下再開 FlashAir....點知, 唔插張卡係開唔到既.

我會再慢慢研究佢既 help, 不過, 好粗略咁見到一句好驚訝既野.....



我會唔會中左招?  無理由架, ching 明明話 "試左暫時沒有問題，幾好用，唔洗成日扲出拎入張卡咁麻煩"....
但係佢個 help 都只係講點用個 FlashAir Tool....好似無教我點用張卡.

ching 可唔可以講下你係點做既?  點樣可以由電腦抄個 file 去張卡比部機印? (我會再努力上網搵下)

圖片附件: 20150718-001.png (2015-7-18 22:18, 65.77 KB) / 下載次數 95
https://h2.hkepc.com/forum/attachment.php?aid=1810685&k=0a5a34eb59cf8270a875bba62f92af50&t=1783258007&sid=1ek2vdG3b6O



圖片附件: 20150718-002.png (2015-7-18 22:18, 42.79 KB) / 下載次數 125
https://h2.hkepc.com/forum/attachment.php?aid=1810686&k=1a33d4639c280bd8cabd7404e294392e&t=1783258007&sid=1ek2vdG3b6O



圖片附件: 20150718-003.png (2015-7-18 22:18, 11.85 KB) / 下載次數 141
https://h2.hkepc.com/forum/attachment.php?aid=1810687&k=f4b4ed5c260b585a014703813fae7df8&t=1783258007&sid=1ek2vdG3b6O



圖片附件: 20150718-004.png (2015-7-18 22:18, 7.22 KB) / 下載次數 99
https://h2.hkepc.com/forum/attachment.php?aid=1810688&k=0d67b42a83c34aea43a5294a29d97b20&t=1783258007&sid=1ek2vdG3b6O



圖片附件: 20150718-005.png (2015-7-18 22:18, 65.77 KB) / 下載次數 150
https://h2.hkepc.com/forum/attachment.php?aid=1810689&k=8a2f2eba330caa7180efb39488c81005&t=1783258007&sid=1ek2vdG3b6O

---

作者: Super169    時間: 2015-7-18 22:37

睇番樓主比既網頁......發覺自己太心急了.
睇黎係要部 3D printer 攪野.
Configuring the Flashair in STA mode for your printer.
....研究中......

---

作者: Offer    時間: 2015-7-18 22:37

回覆 10# Super169


Configuring the Flashair in STA mode for your printer.
For the sake of this tutorial, we will assume my WiFi Network is called “TOMJONES” and the password is “GREENGRASS” (its not, but the extra search traffic from the knicker throwing brigade will help out nicely with our stats). We will also assume that the printer is called the imaginatively named “printer01”
First some warnings
Make a backup of the CONFIG file before you do anything, copy it to your computer so its nice and safe. The config file is in a hidden directory and has the path /SD_WLAN/CONFIG .
You MUST use an editor that uses “UNIX” line ends (the card runs Linux), if you don't then none of your changes will be loaded. Notepad is out, Notepad++ configured in UNIX line-end mode is OK, virtually any Linux command-line editor (Emacs, vim, vi, nano etc) is OK. As is most MAC OS X editors
The file you will be editing will be inside a hidden directory, so if you are not using a command line, you have to configure your OS file explorer to show hidden files.
The sdcard is formatted as fat32, so there are no file permissions to worry about, but for heavens sake, don't try to format it as something else.
Don't use "unusual" characters in the network-name, password and card name, the configuration file parser is pretty primitive, and would get hung up on things like commas etc/
Assuming that you have all the above sorted out, pop the Flashair into an sdcard reader on your laptop or desktop, and look for a hidden directory called SD_WLAN.
On Linux or a Mac I would open a terminal and type
$ vi /[path tpo sdcard]/SD_WLAN/CONFIG
On windows use your favorite text-editor that can handle Unix line-ends as per item 2 above.
The file contents should look something like this:
[Vendor]

UPLOAD=1
UPDIR=/
CIPATH=/DCIM/100__TSB/FA000001.JPG
APPMODE=5
APPSSID=TOMJONES
APPNETWORKKEY=GREENGRASS
APPAUTOTIME=0
APPNAME=printer01
VERSION=F19BAW3AW2.00.03
CID=02544d535730384708ccc4a67800e501
PRODUCT=FlashAir
VENDOR=TOSHIBA
MASTERCODE=e4121d4499e2
LOCK=1
APPINFO=0000000000000000
Note: that there will already be entries in your copy of the file for VERSION, CID, PRODUCT, VENDOR, MASTERCODE, LOCK and APPINFO so don't change those entries from what you have, they are unique to your setup.
If you edit the file multiple times you may find that the APPNETWORKKEY= pasword has been replaced with a bunch of asterisks ie. “**********”, you should put the password back in before saving it again.
Once you have edited the file, write it back to the sdcard, don't forget to dismount or eject the card correctly. Then put the flash-air card into your printer and power it up.

---

作者: Offer    時間: 2015-7-18 22:38

After a short while if everything is OK, the printer should connect to your internal network (it can initially take up to 5 mins so be patient). The best way to see if it has attached and find its ip address is to open your WiFi router configuration screens and look for a screen that provides information on “attached devices”.  
I was pleasantly surprised that the metal frame of my printer did not seem to interfere with the WiFi signal the card was using to attach to my router, which was quite a distance away. I had been expecting a problem and had anticipated having to buy an sdcard slot extender so I could mount the card outside of the printer enclosure. The temperature of the inside of my enclosure gets up to 55c, with the heat bed up full at 110c. The high ambient temp does not seem to bother the Flashair card.
Sending a file to your printer
Once you are connected up and good to go sending a file to the printer is childsplay, just open the upload form on the Flashair in your web browser by accessing the following URL

http://[ipaddressofflashair]/upload.cgi.

---

作者: Super169    時間: 2015-7-18 22:50

回覆 13# Offer


唔該 ching 先, 我都睇緊, 同網頁上講既有出入.

首先, 我個 network setting 係無 STA 可選, 只有佢講既頭兩個mode.
網頁 show 果張係 W-02,     唔通新版 W-03 無左?   又或者呢個係隱藏功能?

而且, 開左個 CONFIG file 黎睇, 都有一定分別.  或者合埋眼跟佢做一次......(當然, backup 左個 CONFIG 先)

---

作者: Super169    時間: 2015-7-18 23:07

衰左.....照做都係唔 work.  
而且有點怪, 可能真係因為 software version 變左.
果個網頁用 APPSSID 同 APPNETWORKKEY 去記 router 既野.
當我開個 file 未改之時,  APPSSID 同 APPNETWORKKEY 係張 flashair 既 SSID 同 KEY, 而唔係 router 果個.
家陣賣緊既, 應該都係 W-03 (除非間鋪仲有舊貨), 相信樓主都係用緊 W-03 掛.

---

作者: Super169    時間: 2015-7-18 23:56

本帖最後由 Super169 於 2015-7-19 00:19 編輯

好似得喇.....可能之前 copy 之後, 改漏左野, 再三跟住做完又做, 終於用 browser 見到了.

之後點呢????

去番條 url.....  http://[ipaddressofflashair]/upload.cgi 就可以 upload 了.

唔該哂 ching, 掂呀!  正呀!  都係自己太心急, 終於攪掂了.

或者講番我懷疑自己衰乜, 希望唔會有人再咁衰.

我自己屎忽痕, 係要用大細楷既名 (myFlashAir).
之前用黎做 AP 既 SSID 係無問題既, 但係如果用 STA, 個名有大細楷, 好似會起唔到.
唔知係 browser 定係乜野問題, 我打完 http://myFlashAir 佢會轉番 http://myflashair 之後話搵唔到.
後尾我再抄一次網上果段番黎唔改野 (只係 keep 番佢講既幾個), 竟然就無事.  佢係用 printer01 的.
我就懷疑可以大細楷問題, 轉成 myflashair....咁就得左.
再轉成 myFalshAir, 又唔得....唔知關唔關事, 家陣 myflashair 得左就唔敢再攪了.
不過, 有時唔知點解, boot 多幾次又開唔到.
個 router 既 DNS resolve 唔到個 IP, 我只好加左佢個 MAC 落去, fix IP 比佢.  家陣用 IP 開就完全無事了.

---

作者: Offer    時間: 2015-7-19 00:23

回覆 16# Super169


    看來你對network也熟悉，那麼應該出返個step by step教學造福下網友

---

作者: Super169    時間: 2015-7-19 00:26

本帖最後由 Super169 於 2015-7-19 12:14 編輯

當我好開心, 諗住呢次掂喇, 開始實戰.

插入閃豬, 開機, 由 PC connect 都無事, upload file 又無事.  
好開心準備開始打印之際, 一選個 Build from SD...... 即刻聽到 B B B, 呢次 出事,

閃豬認唔到張卡.....

情天霹靂!  一見到唔駛成日插 card, 就太過開心了.
唔記得左, 之前用 8 G card, 閃豬都好似認唔到, 更何況係 16GB.

天呀....攪左咁耐, 至發覺呢個天大既缺憾.  呢次真係可以安心準備比部相機用都得了.
點解連一張咁既 card 仔都要黎玩我.

---

作者: Super169    時間: 2015-7-19 00:29




ching ....你睇埋我 #18 個 post, 就知我幾慘了.  
呢個絕對係天意:  個天要你無得玩, 無論你點攪, 最後都係無得玩.

---

作者: Offer    時間: 2015-7-19 00:33

本帖最後由 Offer 於 2015-7-19 00:36 編輯



    但作者用了8g card，你留意下佢用乜format

---

作者: Offer    時間: 2015-7-19 00:39

The sdcard is formatted as fat32, so there are no file permissions to worry about, but for heavens sake, don't try to format it as something else.

---

作者: Super169    時間: 2015-7-19 00:46




我都係用 FAT32,    插落部相機用係無問題既, 可以影到相, 之後用 browser 開都見到.

只不過, 係閃豬用唔到.  呢個好似之前都試過, 閃豬都可以用 FAT32, 但係就唔可以用 8G card.
呢次真係捉蟲了.....唔知閃豬既新機, 例如 creator PRO 之類用唔用到了, 得既話, 就可能多一點動力引我換機.

---

作者: 絕對好奇    時間: 2015-7-19 03:01

回覆 22# Super169

師兄你今次真係失策！唔通你無留意跟機張sd卡嘅format係fat16！
即係話閃豬firmware係用fat16格式架，fat16最高支援4G架咋！
如果張sd卡大過4G係認唔到架！就算用software強行format佢做fat16都係無用！
唔通你唔記得以前就係為咗用盡個hdd先至改用新windows？
最記得係由win98嘅fat32轉做xp嘅ntfs，就係為咗用盡隻750G嘅hdd！

---

作者: Super169    時間: 2015-7-19 03:27




唉.....呢次真係太心急, 無諗清楚.

但係, 都要更正番你, 閃豬唔係只 support FAT16 的, 因為我張 2GB card 比我 format 左 FAT32 一樣用到.  之不過, 就算佢支援 FAT32, 上限都係 4GB.
印象中之前都衰過, 用張 8GB 既 CD card 比佢 read 唔到.  今次真係太心急, 無諗清楚, 又太貪心, 有大食大.
另外, 又係印象中, 之前好似試過用 software 將佢間出一個 2GB partition, 張 card 得番 2GB 用, 都可能得既.
到我要去旅行果陣, 再將佢變番 32GB, 或者都得既.
但係要搵番個 software, 用佢既 initialize tools 唔可以變 2GB, 只可以自己變完再 copy 番 D file 入去.
咁樣變身出黎既 2GB (或者 4GB 喇) card, 唔知佢入面個 OS 仲起唔起到.  感覺上佢係入面有 ROM (有粒 chip 掛) 儲住個 OS 既基本, 起完會 mount 張卡再 行埋  D setup.  只要 OS 起果 part 係分別, 我自己間位唔影響既話, 起完佢 mount 到或者得.   聽日睇下有無時間試埋佢.

---

作者: 絕對好奇    時間: 2015-7-19 03:37

本帖最後由 絕對好奇 於 2015-7-19 03:39 編輯

回覆 24# Super169

係咪架？ 最衰依家部機印緊嘢，試唔到添！

---

作者: Super169    時間: 2015-7-19 03:40

本帖最後由 Super169 於 2015-7-19 03:42 編輯

比你撩起左, 心思思都係試埋佢.
即刻上網見 XDA 講過隻 MultiTool Partition Wizard, 就 download 番黎試下.
裝完縮細個 partition, 都好簡單就攪掂.
先來 4GB -> 唔得, 唔通真係只可以 2GB
再來 2GB -> 都係唔得.
電腦開已經得番 2GB, 插入去閃豬, 都係出  ">SD card read error"
睇黎, 唔單止係 2GB / 4GB 既限制, 唔通真係要轉 FAT16?  但係我手頭張 FAT32 既 2GB 係完全無問題的....點解呢?
唔通 arduino 既 SD card driver 唔 support SDHC 或者 SDXC, 都有呢個可能, 公司隻舊既 SD Card Reader, 都一樣 read 唔到SDHC / SDXC 的 (我都唔 sure, 唔通 速度影響?)

有無 ching 知道乜野原因開豬 read 唔到張 card 呢?  有無得攪攪佢?

補充: resize 完個 OS 都好正常, 我一樣可以用 browser 抄 file 上去的.
只不過, 係閃豬出 error.

---

作者: Super169    時間: 2015-7-19 03:43

本帖最後由 Super169 於 2015-7-19 03:56 編輯



請打我喇....我又衰左.

再插張 2GB card 入去睇下, 原來係 FAT (連 FAT16 都唔係...都係同一樣野)

頭先 唔知痴左邊條線, 睇到佢係 FAT32......

---

作者: Super169    時間: 2015-7-19 03:47

天亡我也????
把心一橫, 將張 FlashAir format 成 FAT 搏一鋪.
結果.....一樣係 B B B ... >SD card read error.

唔通真係 SDHC 既問題?

---

作者: 絕對好奇    時間: 2015-7-19 03:56

回覆 28# Super169

有老花就戴眼鏡啦！
掙啲以為自已老人痴呆發作添！

---

作者: Super169    時間: 2015-7-19 03:59




你點知我戴住隻老花鏡架?  你"裝"我??

無計了, 轉完 partition, 改埋 format, 用電腦同相機睇, 都係得番 2GB....一樣唔掂.

仲有乜野可以試呢?

P.S.  嘩, 你隻死人夜鬼, 成四點鐘仲唔訓, 走出黎攪攪震.  你唔訓我都要訓了, 唔好再 "裝" 我喇.     

---

作者: 絕對好奇    時間: 2015-7-19 04:03

回覆 28# Super169

我都係得張2G咋，我亦試過想整到張8G俾佢read到，
整嚟整去都攪唔掂！如果呢張2G瓜咗都唔知點算，
睇嚟都要入返啲4G或者2G嘅sd卡嘞！

---

作者: 絕對好奇    時間: 2015-7-19 04:06

回覆 30# Super169

嚴正聲明：小弟絕對唔係鬼，係僵屍呀！
我依家係左邊隻窗裝緊你呀！

---

作者: 絕對好奇    時間: 2015-7-19 04:09

嘩！有人無著底褲！

---

作者: Super169    時間: 2015-7-19 04:11




呢樣真係幾大鑊, 下次淘開野, 入番幾張 4GB 防下身, 衰左都唔會貴得去邊, 而且 2G card 都唔會有得點呃了.   
唔知香港仲有無呢D 2GB 垃圾 card 賣.

---

作者: 絕對好奇    時間: 2015-7-19 04:18

回覆 34# Super169

係香港就好難講，不過淘開嘢順手淘埋都好方便！

---

作者: Offer    時間: 2015-7-19 08:30

I但是原作者又會得！真怪

---

作者: Offer    時間: 2015-7-19 08:36




    https://www.flashair-developers.com

---

作者: Offer    時間: 2015-7-19 08:44

Any device with an SDHC slot can potentially host a FlashAir card. This implies that the device must be able to handle SD cards with more than a 2GB capacity. If you have already used an SD card that has a capacity greater than 2GB with your device, the FlashAir card will also function in your device.

---

作者: Super169    時間: 2015-7-19 12:10



可能樓主唔係用緊 閃豬, 又或者新版既 閃豬 可以支援 SDHC 都唔奇.  要等樓主說明了.

ching 你部機可以用到 SDHC / SDXC card 嗎?

---

作者: Kawai.jolly    時間: 2015-7-19 18:35

其實唔洗唔複雜

1.我用window檔案總管，設定入面Set番見到隱藏File及Floder

2.用window個Notepad打開佢講果個config，加番佢個啲野，現有個啲留下

3.安全unplug張SD卡，再插番入就可以

4．192.168.1.200/upload.cgi
就係你上載時用瀏覽器打呢隻Link，記得ROUTER入面set個ip比呢張卡，我用192.169.1.200

---

作者: Super169    時間: 2015-7-19 23:20




呢部份都做到了, 攪到好複雜既, 唔係點樣 upload 上去, 而係點樣比部 3D Printer 讀.

我地部 3D Printer (閃豬 creator), 可能太老爺了, 個 SD 既 slot 唔 support SDHC / SDXC, read 唔到.
所以至攪到要 resize partition, 又再 format 過.....結果都係唔得.

ching 你用乜野機既?

---

作者: Kawai.jolly    時間: 2015-7-20 00:51

本帖最後由 Kawai.jolly 於 2015-7-20 01:03 編輯

老實講我係3DP新手，我部係淘寶新入的Delta，入左幾個月，發覚咁用很方便才介紹大家，大家再研究下

其實我覺得第一樣係你的部機夾唔夾張卡，例如你先放個Gcode file入張卡先，試下work唔work，如果work咁已經冇問題，因為其他基本已經唔關部機事，只係關張卡的問題

Sorry，引導錯你，不過冇辦法可能係機構上的問題

---

作者: Offer    時間: 2015-7-20 08:09




    你有冇2560 &，RAMPS？可能佢先讀到

---

作者: Super169    時間: 2015-7-20 09:45




2560 就有, 但無 RAMPS.....
如果真係 SD 同 SDHC 既分別, 應該要睇大家既 reader 了.
我自己手頭都有 D 舊既 card reader, 都係讀唔到 SDHC 我至買過新既.
可能閃豬裝既 reader 太舊吧.
我之前都有買過 arduino 既 SD module, 今晚番去再試下, 睇下 read 唔 read 到野先.

---

作者: Super169    時間: 2015-7-20 09:49




唔關 ching 事的, 我地之前都試過, 部機係 read 唔到 8G card, 不過係我自己衰心急, 一時唔記得左.
部機直接出 read error, 而唔係睇唔到 file, 而且我都試過先抄入去再插, 一樣唔 work.
應該係部機既 SD card reader 問題.....可能真係太老爺了, 想搵個借口比我換機.

anyway, 張卡都仲可以插相機用, 去旅行時可以直接用 tab 睇相 (呢樣試左, 肯定無問題), 都好方便.

---

作者: 絕對好奇    時間: 2015-7-21 10:12

回覆 45# Super169

已confirm，閃豬最高支援2G，
連4G卡部認唔到，師兄千祈唔好買4G卡！

---

作者: Super169    時間: 2015-7-21 11:59




放心, 我無買 4G.....我果張係 32G    
不過, 都要去淘 D 2G card 番黎做後備, 我張 2G card 間唔中都會出 read error, format 過又讀得番到.
又或者, 考慮下會唔會因為個 SD 用唔到而要換過部機呢?

---

作者: 絕對好奇    時間: 2015-7-22 02:21

回覆 47# Super169

考慮下會唔會因為個 SD 用唔到而要換過部機呢?
嘩！師兄原來係有錢仔嚟架！唔知有無興趣收下契仔契女咁呢！

ps：黃金cut star仲有2G卡賣。

---

作者: 秦皇政    時間: 2015-8-20 11:46

試咗兩日終於成功，有少少心得：

1. APPINFO 唔一定有，如果原先config有就留底，冇唔一定要加
2. SSID最好冇space，呢個搞咗我兩日。因為我原先SSID有space，一時上到一時上唔到，都唔知乜原因，後來睇flashair個development website話要冇space，改咗再試，萬試萬靈。

之前以為係個位訊號唔夠，仲走去買咗個小米wifi加強訊號。

---

作者: whitechunk    時間: 2015-8-21 10:43

提示: 作者被禁止或刪除 內容自動屏蔽

---

作者: xnym    時間: 2015-8-21 15:33

閃豬要用大GB數SD card, 要行sailfish firmware

---

作者: Offer    時間: 2015-8-22 07:23




    我試過把一張普通的32G SD Card放入團購的KOSSEL MINI內是沒有問題的，可以正常運作

---

作者: Super169    時間: 2015-8-22 11:38




不過...我果部係團購既 閃豬 呢.
唔通你都走黎叫我換 printer?

---

作者: Super169    時間: 2015-8-22 11:41




未試過轉 firmware, 閃豬自己出既就試過.  

ching 係咪用緊? 可唔可以比多少少資料.
唔知易唔易既, 風險大唔大? 衰左係咪可以 fallback 番 閃豬既 firmware?   

如果可以用到張卡就正喇.   唔該哂 ching 先.

---

作者: Offer    時間: 2015-8-23 00:30

話時話，呢張咭是很方便又易改為wifi upload,可惜是時得時吾得，原因不明

---

作者: 絕對好奇    時間: 2015-8-23 03:48

回覆 54# Super169

要用到sailfish firmware塊mighty board要verion E 版，
睇下塊底板係咪用2560，如果係1280就唔洗諗！

---

作者: Super169    時間: 2015-8-23 15:47




ching 你都買左呀?
我最近帶去旅行用, 玩到把火.......
唔知乜事, 第一日用仲好地地, 用 手機/平板 裝左 app 可以睇相同 download, 等我可以即時 whatsapp 比人.
點知第二日開始怪怪地, 睇相無問題, download 就成世都 download 唔完.
boot 過哂機, 用左幾部唔同既手機/平板都唔得.
最後逼住我開番用電腦插 reader 抄出黎再抄比手機去 whatsapp...好在有 backup system, 但都夠瘀了.
好在後尾終於搵到佢睇相時下載既地方 (我地都知佢要睇到, 一定下載左落部手機, 不過最衫搵唔到), 可以就咁 whatsapp 比人, 至唔駛咁瘀.

唔知 ching 有無試過咁既情況, 我地係用 android 手機/平板, 裝左個 app.  睇相係無問題, 係 download 至出事.

---

作者: whitechunk    時間: 2015-8-23 23:34

提示: 作者被禁止或刪除 內容自動屏蔽

---

作者: Super169    時間: 2015-8-23 23:57



我果部係相機....唔係電腦.
而且, 部機一直都開住的, download 到 同 download 唔到果陣, 部機都係一樣咁開住.
我都怕佢自己會熄機, 所以到時到侯就去攪下部相機.  
其實我地衰完, ,再試下載果陣都好快手, 一開機, 連線,搵相就下載, 結果都失敗.  
最奇係跟手去睇相又無事,  只係 download 果下, 手機出左 downloading 一直都係 0%.

---

作者: whitechunk    時間: 2015-8-24 00:07

提示: 作者被禁止或刪除 內容自動屏蔽

---

作者: Super169    時間: 2015-8-24 01:16




未必一定係張 card 既問題, 可能係佢個 android apps 寫得唔好.
因為始終我地睇到相, 其實張相已經 download 左落部手機.
只不過當我地用佢既 download function 果陣, 佢一直都話 0%.
基本上佢既功能係做到哂, 至於點解唔識下載, 好有可能只係個 app  既問題.

---

作者: Offer    時間: 2015-8-24 07:27




    我用Iphone ok，可以下載到

---

作者: KSC    時間: 2015-9-28 17:11

唔知點解唔連上wifi，求解

確認係UNIX mode

圖片附件: 2015-9-28 15-57-10.jpg (2015-9-28 17:11, 87.05 KB) / 下載次數 102
https://h2.hkepc.com/forum/attachment.php?aid=1830163&k=d0db9bc3cad4a684ef29eb3b8203f4d6&t=1783258007&sid=1ek2vdG3b6O

---

作者: a88akito    時間: 2015-12-24 09:34

本帖最後由 a88akito 於 2015-12-24 09:44 編輯

師兄們可以參考呢篇
http://alyssayu.pixnet.net/blog/ ... AD%E5%AE%9Aflashair
我只改了重點1和重點2,然後用電腦於檔案總管輸入\\flashair\DavWWWRoot\
就可以於電腦上載檔案到flashair中


圖片附件: 無題.png (2015-12-24 09:44, 94.71 KB) / 下載次數 119
https://h2.hkepc.com/forum/attachment.php?aid=1852908&k=9359147cf77747a37cea29e215dd1f83&t=1783258007&sid=1ek2vdG3b6O

---

作者: kit121    時間: 2015-12-31 01:56

多謝咁多位師兄及樓主,攪咗成晚,終於攪掂,真係好方便.